Customer Support
0
Close

Categories

Filters

    Soil Temperature and Moisture probe 3 m - USB for WS1 Pro

    €55,-
    €34,-Excl. tax Product is in stock : We ship immediately !
    Ubibot Soil Temperature and Moisture probe 3 m - USB for WS1 Pro... Show more
    • B2B Industrial Supplier since 1999
    • Shipping from our own warehouse in NL !
    • Shipping in EU with DPD Traceable
    • Reliable SSL & Secure Payments

    Product description

    Download Datasheet Download PDF

    Soil Temperature and Moisture probe 3 m - USB for WS1 Pro

    • This model pairs our WS1 and WS1 Pro devices
    • Support switch between RH and AH
    • Electrolysis-resistant
    • Accurate, fast data acquisition
    • Stainless steel probe

    This probe specialises in monitoring temperature and humidity of soil. Embedded with industrial-grade chip, the probe offers accurate measurement. The stainless steel probe can be inserted into the soil for a long term without being corroded. The durable cable ensures stable data transmission.

    The measurements are transferred to the devices, displayed on the large LCD screen and synced to the platform via network. So you can access the data instantly on the screen or remotely view them via our app or web console.

    The humidity readings on the app can be switched between Relative Humidity and Absolute Humidity. You can configure the display on the web console.

    Application Instructions

    For one time use only

    Insert the steel probe point vertically to the soil at your preferred depth. Hold the probe tightly in case of it shaking. Avoid touching stones or any other hard objects, because that will damage the probe. Please wait for about 20 minutes to allow the sensor to work properly.

    For long time burried in soil:

    Dig a hole at over 20cm-diameter on the ground or soil in your greenhouse. Insert the steel probe point in horizontal direction to the soil. Leave the probe in the soil and you can have your data remotely.

    About humidity readings

    All soil probes have been calibrated in the factory. Calibration including data points is conducted by placing the probe in the air to reach the minimum of 0% and pure water to reach the maximum 100%. For very wet soil, the reading is expected to be around 30% depends on the soil type. Please note that when the soil is waterlogged, the reading may jump from the values of 30%-35% to 100% as it is very close to the situation of soaking the probe in the pure water.

    Reminder

    The external sensors of the WS1 Pro device are disabled by default . Please enable them in the "Settings" page on the App or the console after inserting the probe into the device. In this case, the readings from the external probe are accessbile. The button "RS485 S" refers to this soil probe. The GS1 device doesn't need this operation.

    Warning: The probe point is very sharp. Be careful when using it and keep it away from children.

    Specifications : 

    Steel Point Length : 80mm
    Length of Cable : 300cm
    Material : ABS
    Connector : Micro USB & Audio Plug
    Power Supply Range : DC 5V to 12V
    Operating Condition : -40°C to +85°C, 0 to 100% RH
    Accuracy ±0.5°C
    Output Interface : RS485
    Communications Protocol : Modbus

    Specifications

    Article number
    Soil-Probe-USB-3M
    SKU
    Soil-Probe-USB-3M
    Soil Temperature and Moisture probe 3 m - USB for WS1 Pro
    € 55,-
    € 34,-
    Excl. tax
    Soil Temperature and Moisture probe 3 m - USB for WS1 Pro
    Soil-Probe-USB-3M
    Product is in stock : We ship immediately !
    Add to cart

    Recently viewed

    Compare 0

    Add another product (max. 5)

    Start comparison

    Please accept cookies to help us improve this website Is this OK? YesNoMore on cookies »