Klantenservice
0
Sluiten

Categorieën

Filters

    Need help ?

    Give us a call and we will assist !

    + 31-(0)85-065 6325

    Erkend distributeur voor :

    Prijs

    -
    13 Producten
    LJTick-Resistance

    LJTick-Resistance

    The LJTick-Resistance (LJTRx) makes it easy for LabJack devices to measure resistive sensors.

    € 41,62 Excl. btw
    Bekijken
    LJTick-DigitalOut5V

    LJTick-DigitalOut5V

    Converts 3.3V digital outputs to 5V digital outputs. Easily control 5V relays, or interface with a 5V logic device.

    € 24,05 Excl. btw
    Bekijken
    LJTick-InBuff

    LJTick-InBuff

    Very low bias current (1pA) input buffer which can directly measure pH sensors (electrode type sensors) and other weakly driven or high source impedance signals. The analog inputs on our compatible DAQ products (U3, U6, UE9, T7) have typical bias cu...

    € 43,47 Excl. btw
    Bekijken
    LJTick-VRef-41

    LJTick-VRef-41

    Voltage reference accessory that outputs a stable 4.096V. Commonly used as an excitation voltage for bridge circuits. Simply attach the supply side of the bridge to the 4.096 terminal, and ground to the GND terminal. The IOA and IOB lines are simply...

    € 37,- Excl. btw
    Bekijken
    LJTick-OutBuff

    LJTick-OutBuff

    Increases the output current of the DAC outputs on LabJack devices. Can also be used for switched 3.3V when attached to a 3.3V digital I/O line. LabJack devices cannot output more than about 15mA on their DAC0 and DAC1 analog outputs, so this accesso...

    € 23,12 Excl. btw
    Bekijken
    LJTick-LVDigitalIO

    LJTick-LVDigitalIO

    A bidirectional logic shifting board for converting 3.3V logic down to 2.5V or 1.8V. There is also a VOUT terminal which can source power at the selected voltage. Useful for users who have external boards that run on lower logic thresholds, or simply...

    € 17,57 Excl. btw
    Bekijken
    LJTick-VRef-25

    LJTick-VRef-25

    Voltage reference accessory that outputs a stable 2.5V. Commonly used as an excitation voltage for various circuits. The IOA and IOB lines are pass-through terminals, and do not interact with the accessory in any way.

    € 37,- Excl. btw
    Bekijken
    LJTick-Proto

    LJTick-Proto

    The LJTick-Proto (LJTP) consists of an 8x8 grid of holes for prototyping custom signal-conditioning ticks. The 4-pin design plugs into the standard AIN/AIN/GND/VS screw terminal block found on newer LabJacks such as the U3 and UE9. Includes 3 loose p...

    € 9,25 Excl. btw
    Bekijken
    LJTick-DAC

    LJTick-DAC

    Provides a pair of 14-bit analog outputs with a range of +/- 10 volts. Plugs into any digital I/O block, and thus up to 10 of these can be used per LabJack to add 20 analog outputs. Works with any UD family device (U3/U6/UE9), except for U3 hardware ...

    € 87,87 Excl. btw
    Bekijken
    LJTick-InAmp

    LJTick-InAmp

    Signal-conditioning module provides two instrumentation amplifiers ideal for low-level signals such as bridge circuits (e.g. strain gauges) and thermocouples.

    € 83,25 Excl. btw
    Bekijken
    LJTick-RelayDriver

    LJTick-RelayDriver

    The LJTick-RelayDriver allows 2 digital I/O lines on a U3, U6, or UE9 to each control a relay or other moderate load.

    € 16,65 Excl. btw
    Bekijken
    LJTick-Divider

    LJTick-Divider

    Signal-conditioning module designed to divide 2 single-ended channels of higher voltage analog signals down to 0-2.5 volt signals.

    € 32,37 Excl. btw
    Bekijken
    LJTick-CurrentShunt

    LJTick-CurrentShunt

    signal conditionning unit from 4-20 mA signals.

    € 60,12 Excl. btw
    Bekijken
    Vergelijk 0

    Voeg nog een product toe (max. 5)

    Start vergelijking

    Wij slaan cookies op om onze website te verbeteren. Is dat akkoord? JaNeeMeer over cookies »