Customer Support
0
Close

Categories

Filters

    Need help ?

    Give us a call and we will assist !

    + 31-(0)85-065 6325

    Authorised Distributor for :

    Price

    -
    13 Products
    LJTick-Resistance

    LJTick-Resistance

    The LJTick-Resistance (LJTRx) makes it easy for LabJack devices to measure resistive sensors.

    € 41,62 Excl. tax
    View
    LJTick-DigitalOut5V

    LJTick-DigitalOut5V

    Converts 3.3V to 5V digital outputs digital outputs. Easily control 5V relays, or interface with a 5V logic device.

    € 24,05 Excl. tax
    View
    LJTick-InBuff

    LJTick-InBuff

    Very low bias current (1pA) input buffer-which can directly measure pH sensors (electrode type sensors) and other weakly driven or high source impedance signals. The analog inputs on our compatible DAQ products (U3, U6, UE9, T7) have typical bias cu ...

    € 43,47 Excl. tax
    View
    LJTick-VRef-41

    LJTick-VRef-41

    That accessory voltage reference outputs a stable 4.096V. Commonly used as an excitation voltage for bridge circuits. Simply attach the supply side of the bridge to the 4096 terminal, and ground to the GND terminal. The IOA and IOB lines are simply ....

    € 37,- Excl. tax
    View
    LJTick-OutBuff

    LJTick-OutBuff

    Increases the output current of the DAC outputs on Labjack devices. Can also be used for switched 3.3V When attached to a 3.3V digital I / O line. Labjack devices can not output more than about 15mA On Their DAC0 DAC1 and analog outputs, so this acce...

    € 23,12 Excl. tax
    View
    LJTick-LVDigitalIO

    LJTick-LVDigitalIO

    A bidirectional shifting logic board for converting 3.3V down to 2.5V or 1.8V logic. There is ook a VOUT terminal-which can power source at the selected voltage. Useful for users who have external boards That run on lower logic thresholds, or simply ...

    € 17,57 Excl. tax
    View
    LJTick-VRef-25

    LJTick-VRef-25

    That accessory voltage reference outputs a stable 2.5V. Commonly used as an excitation voltage for various circuits. The IOA and IOB lines are pass-through terminals, and do not interact with the accessory in any way.

    € 37,- Excl. tax
    View
    LJTick-Proto

    LJTick-Proto

    The LJTick-Proto (LJTP) Consists of an 8x8 grid of holes for prototyping custom signal-conditioning ticks. The 4-pin design plugs into the standard AIN / AIN / GND / VS screw terminal block found on newer LabJacks zoals the U3 and UE9. Includes three...

    € 9,25 Excl. tax
    View
    LJTick DAC

    LJTick DAC

    Provides a pair of 14-bit analog outputs with a range of +/- 10 volts. Plugs into any digital I / O block, and osmanthus up to 10 or thesis can be used by Labjack to add 20 analog outputs. Works with any family UD device (U3 / U6 / UE9), except for U3 har

    € 87,87 Excl. tax
    View
    LJTick-InAmp

    LJTick-InAmp

    Signal conditioning module biedt two instrumentation amplifiers ideal for low-level signals zoals bridge circuits (eg strain gauges) and thermocouples.

    € 83,25 Excl. tax
    View
    LJTick Relay Driver

    LJTick Relay Driver

    The LJTick Relay Driver Allows two digital I / O lines on a U3, U6, or UE9 to each control a relay or other moderate load.

    € 16,65 Excl. tax
    View
    LJTick-Divider

    LJTick-Divider

    Signal conditioning module designed to divide two single-ended channels or higher voltage analog signals down to 0-2.5 volt signals.

    € 32,37 Excl. tax
    View
    LJTick-Current Shunt

    LJTick-Current Shunt

    voltage signal conditioning unit from 4-20 mA signals.

    € 60,12 Excl. tax
    View
    Compare 0

    Add another product (max. 5)

    Start comparison

    Please accept cookies to help us improve this website Is this OK? YesNoMore on cookies »