High Perforemance Multifunction DAQ with, Ethernet, and USB, 16-bit ADC, 100kS/s, Plus 802.11b/g WiFi & 24-bit ADC
LabJack U3-HV. USB based multifunction data acquisition and control device, with 16 Flexible IO.
USB of Ethernet multifunctioneel DAQ-apparaat met maximaal 12 analoge ingangen of 16 digitale I / O, 2 analoge uitgangen (10-bit) en meerdere digitale tellers / timers
Provides convenient screw terminals for the DB37 connector on the LabJacks. Includes a screwdriver. Is compatible with LJTick signal-conditioning modules.
LabJack T8 - The new flagship DAQ from LabJack USA
USB-based multifunction data acquisition and control. A breakthrough price/performance ratio. This is the original LabJack from LabJack Corporation USA !
High Performance Multifunction DAQ with, Ethernet, and USB, 16-bit ADC, 100kS/s.
Provides a pair of 14-bit analog outputs with a range of +/- 10 volts. Plugs into any digital I/O block, and thus up to 10 of these can be used per LabJack to add 20 analog outputs. Works with any UD family device (U3/U6/UE9), except for U3 hardware ...
Labjack U6, 16+ bits of resolution, Wide input range, Amazing price performace ratio
Labjack U6-PRO, 24 bit sigma-delta AD, Wide input range, Amazing price performace ratio
Signal-conditioning module designed to divide 2 single-ended channels of higher voltage analog signals down to 0-2.5 volt signals.
Easy to use and very accurate temperature probe. Features a waterproof stainless-steel probe, a high-level linear output of 10 mV per degree F, a typical accuracy of ±0.4 °F (±0.22 °C) at room temperature, and a range of 0 to +300 °F (-17 to +150 °C,...
The Mux80 is an analog input expansion board that increases the number of analog inputs possible for a LabJack unit. It can be connected to a U6 or UE9 directly through the DB37 connector. Ten of the LabJack's analog inputs are multiplexed (1:8 each...
Signal-conditioning module provides two instrumentation amplifiers ideal for low-level signals such as bridge circuits (e.g. strain gauges) and thermocouples.
Voltage reference accessory that outputs a stable 4.096V. Commonly used as an excitation voltage for bridge circuits. Simply attach the supply side of the bridge to the 4.096 terminal, and ground to the GND terminal. The IOA and IOB lines are simply...
The LM34CAZ is the most accurate version of the LM34 precision temperature sensor made by Texas Instruments. It has a very convenient output of 10mV per °F, so 0.78V would correspond to 78°F.
Converts 3.3V digital outputs to 5V digital outputs. Easily control 5V relays, or interface with a 5V logic device.
The RB12 provides a convenient interface to industry standard I/O modules, allowing electricians, engineers, and other qualified individuals, to interface a LabJack with high voltages/currents. Logic buffers are used to provide the 10-15 mA needed fo...
The LJTick-Resistance (LJTRx) makes it easy for LabJack devices to measure resistive sensors.
Increases the output current of the DAC outputs on LabJack devices. Can also be used for switched 3.3V when attached to a 3.3V digital I/O line. LabJack devices cannot output more than about 15mA on their DAC0 and DAC1 analog outputs, so this accesso...
signal conditionning unit from 4-20 mA signals.
Easy to use and inexpensive temperature probe. Features a plastic probe, a high-level linear output of 10 mV per degree K, a typical accuracy of ±1°C (±1.8°F) at room temperature, and a range of -40 to +100 °C (-40 to +212 °F).
The TKAD DIN rail mounting clip is used for mounting a LabJack device to a DIN rail.
